Show pageOld revisionsBacklinksBack to top This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong. ====== Status and Fault List ====== ^Address^Bit^Flag^Flag category^Flag name in Chinese^Value^ |32|Bit0| Fault status|Fault|故障: 故障综合|0: False; 1:ture| |32|Bit1| Alert status|Warning|告警: 告警综合|0: False; 1:ture| |32|Bit2 |On/Off status|Status|状态: 已开机|0: False; 1:ture| |32|Bit3 |On-grid|Status|状态: 并网|0: False; 1:ture| |32|Bit4 |Off-grid(Island mode)|Status|状态: 离网|0: False; 1:ture| |32|Bit5 |Reserved|||| |32|Bit6 |Reserved|||| |32|Bit7 |Reserved|||| |32|Bit8-15 |Reserved|||| |33|Bit0-7 |Reserved|||| |33|Bit8 |anti-islanding function enabled|Status|状态: 孤岛保护使能|0: False; 1:ture| |33|Bit9-15 |Reserved|||| |34|Bit0-7 |Reserved|||| |34|Bit8-15 |Reserved|||| |35|Bit0-7 |Reserved|||| |35|Bit8-15 |Reserved|||| |36|bit0 |AC OVP|Warning|告警: 交流侧过压保护|0: False; 1:ture| |36|Bit1 |AC UVP|Warning|告警: 交流侧欠压保护|0: False; 1:ture| |36|Bit2 |AC OFP|Warning|告警: 交流侧过频保护|0: False; 1:ture| |36|Bit3 |AC UFP|Warning|告警: 交流侧欠频保护|0: False; 1:ture| |36|Bit4 |Grid voltage unbalance. |Warning|告警: 电网电压不平衡|0: False; 1:ture| |36|Bit5 |Grid phase reverse|Warning|告警: 电网电压反序|0: False; 1:ture| |36|Bit6 |Anti-islanding scheme taking effect (and grid is out)|Status|状态: 孤岛状态|0: False; 1:ture| |36|Bit7 |On/off-grid switching error|Warning|告警: 并离网切换故障|0: False; 1:ture| |36|Bit8 |Output grounding error|Fault|故障: 输出接地故障|0: False; 1:ture| |36|Bit9 |Reserved|||| |36|Bit10 |Grid phase lock failed|Warning|告警: 电网锁相失败|0: False; 1:ture| |36|Bit11 |Internal air over-temp|Warning|告警: 内部环境温度过温|0: False; 1:ture| |36|Bit12 |Enabling grid-tieing criterion detecting timeout|Status|状态: 并网条件判断超时使能|0: False; 1:ture| |36|Bit13-15 |Reserved|||| |37|Bit0 |EPO(Emergency Power-off) tripping|Warning|告警: 急停按钮被按下|0: False; 1:ture| |37|bit1 |HMI parameters fault|Fault|故障: 监控参数故障|0: False; 1:ture| |37|Bit2 |DSP version error|Fault|故障: DSP软件版本错误|0: False; 1:ture| |37|Bit3 |CPLD version error|Fault|故障: CPLD软件版本错误|0: False; 1:ture| |37|Bit4 |Hardware Version error|Fault|故障: 硬件版本错误|0: False; 1:ture| |37|Bit5 |Communication error|Fault|故障: 通讯错误|0: False; 1:ture| |37|Bit6 |Aux power error|Fault|故障: 辅助电源错误|0: False; 1:ture| |37|Bit7 |Fan failure|Fault|故障: 风扇故障|0: False; 1:ture| |37|Bit8 |BUS over voltage|Warning|告警: 母线电压过压|0: False; 1:ture| |37|Bit9 |BUS low voltage|Warning|告警: 母线电压欠压|0: False; 1:ture| |37|Bit10 |BUS voltage unbanlaced|Warning|告警: 母线电压不平衡|0: False; 1:ture| |37|Bit11 |Reserved|||| |37|Bit12 |Reserved|||| |37|Bit13 |Output voltage abnormal.|Fault|故障: 输出电压异常|0: False; 1:ture| |37|Bit14 |Output current unbalanced|Fault|故障: 输出电流不平衡|0: False; 1:ture| |37|Bit15 |Over-temperature of heat sink|Warning|告警: 散热器过温|0: False; 1:ture| |38|Bit0 |Output Overload|Warning|告警: 输出过载|0: False; 1:ture| |38|Bit1 |Reserved|||0: False; 1:ture| |38|Bit2 |AC relay short-circuit.|Fault|故障: AC继电器短路|0: False; 1:ture| |38|Bit3 |Inverter start failure. |Fault|故障: 逆变器启动失败|0: False; 1:ture| |38|Bit4 |AC relay is open. |Fault|故障: AC继电器开路|0: False; 1:ture|AC switch S2 |38|Bit5-15 |Reserved|||0: False; 1:ture| |39|Bit0 |EE Reading error 1|Fault|故障: EE读取错误1|0: False; 1:ture| |39|Bit1 |EE Reading error 2|Fault|故障: EE读取错误2|0: False; 1:ture| |39|Bit2 |Reserved|||| |39|Bit3 |Inverter over load|Warning|告警: 逆变器过载|0: False; 1:ture| |39|Bit4-15 |Reserved|||| |40|bit0 |DC charging|Status|状态: DC充电中|0: False; 1:ture| |40|bit1 |DC discharging|Status|状态: DC放电中|0: False; 1:ture| |40|bit2 |Battery fully charged|Status|状态: 电池充满|0: False; 1:ture| |40|bit3 |Battery empty|Status|状态: 电池放空|0: False; 1:ture| |40|Bit4 |Reserved|||| |40|Bit5 |Reserved|||| |40|Bit6-15 |Reserved|||| |41|Bit0-7 |Reserved|||| |41|Bit8-15 |Reserved|||| ||42|Bit0-7 |Reserved|||| ||42|Bit8-15 |Reserved|||| ||43|Bit0-7 |Reserved|||| |43|Bit8-15 |Reserved|||| |44|Bit0 |DC input OVP(over voltage protection)|Warning|告警: DC输入过压保护|0: False; 1:ture| |44|Bit1 |DC input UVP(under voltage protection)|Warning|告警: DC输入欠压保护|0: False; 1:ture| |44|Bit2 |Reserved|||| |44|Bit3 |BMS Alerts.(available only BMS connected)|Warning|告警: BMS告警|0: False; 1:ture| |44|Bit4-7 |Reserved|||0: False; 1:ture| |44|Bit8-15 |Reserved|||0: False; 1:ture| |45|bit0 |DC soft-start failed. |Warning|告警: DC软起动失败|0: False; 1:ture| |45|bit1 |DC relay short-circuit.|Fault|故障: DC继电器短路|0: False; 1:ture| |45|bit2 |DC relay short-open|Fault|故障: DC继电器开路|0: False; 1:ture| |45|Bit3 |Battery power over load.|||0: False; 1:ture| |45|Bit4 |DC BUS starting failed|Warning|告警: 母线启动失败|0: False; 1:ture| |45|Bit5-7 |Reserved|||| |45|Bit8-15 |Reserved|||| |46|Bit0-7 |Reserved|||| |46|Bit8-15 |Reserved|||| |47|Bit0 |DC OCP|Warning|告警: DC过流保护|0: False; 1:ture| |47|Bit1-7 |Reserved|||| |47|Bit8-15 |Reserved|||| |48-63| |Reserved|||| manual/pws2-30k/status_and_fault_list.txt Last modified: 2020/09/16 22:16(external edit)