Differences

This shows you the differences between two versions of the page.

--- manual:module-based:recommended_grid_support_settings [2019/07/07 21:39]
admin [Enabling]
+++ manual:module-based:recommended_grid_support_settings [2020/09/16 22:16] (current)
@@ Line 26: / Line 26: @@
 ==== Frequency Ride-through ====
 ^Parameter on HMI (legacy name before M1330)  ^Meaning   ^HECO requirement  ^CA rule 21 requirement  ^IEEE1547 requirement  ^
-|Setting -> AC -> Page 6 -> OFR# voltage| Over-frequency region # boundary , bias of nominal frequency |OFR1 frequency: 3 (+60Hz)\\  OFR2 frequency:<WRAP>
+|Setting -> AC -> Page 6 -> OFR2 voltage| Over-frequency region 2 boundary, bias of nominal frequency |<WRAP>
   * 5 (+60Hz) for Molokai, Lanai
   * 4 (+60Hz) for Oahu, Maui, Hawaii
 </WRAP>  |
-|Setting -> AC -> Page 6 -> OFR#  time| Over-frequency region # trip time, -0.5~-1s later than ride-through until |OFR1 time: 20 s, making ride-through 19.98 s \\  OFR2 time: 0.1s, no ride through |
+|Setting -> AC -> Page 6 -> OFR2  time| Over-frequency region 2 trip time, -0.5~-1s later than ride-through until |0.1s, no ride through |
-|Setting -> AC -> Page 6 -> UFR# voltage| Under-frequency region # boundary, bias of nominal frequency| OFR1 frequency: -3 (+60Hz)\\  OFR2 frequency: <WRAP>
+|Setting -> AC -> Page 6 -> OFR1 voltage| Over-frequency region 1 boundary, bias of nominal frequency |3 (+60Hz)  |
+|Setting -> AC -> Page 6 -> OFR1  time| Over-frequency region 1 trip time, -0.5~-1s later than ride-through until |20 s, making ride-through 19.98 s |
+|Setting -> AC -> Page 6 -> UFR1 voltage| Under-frequency region 1 boundary, bias of nominal frequency|-3 (+60Hz)|
+|Setting -> AC -> Page 6 -> UFR2 voltage| Under-frequency region 1 boundary, bias of nominal frequency|<WRAP>
   * -10 (+60Hz) for Molokai, Lanai
   * -4 (+60Hz) for Oahu, Maui, Hawaii
 </WRAP> |
-|Setting -> AC -> Page 6 -> UFR# time |Under-frequency region # trip time, -0.5~-1s later than ride-through until |UFR1 time: 20 s, making ride-through 19.98 s\\ UFR2 time: 0.1s, no ride through |
+|Setting -> AC -> Page 6 -> UFR1 time |Under-frequency region 1 trip time, -0.5~-1s later than ride-through until |20 s, making ride-through 19.98 s|
+|Setting -> AC -> Page 6 -> UFR2 time |Under-frequency region 2 trip time, -0.5~-1s later than ride-through until |0.1s, no ride through |
 |Setting -> AC -> Page 6 -> Restore upper limit freq |Grid reconnect threshold frequency-upper limit, bias of nominal frequency| 0.1 (+60Hz) |
 |Setting -> AC -> Page 6 -> Restore lower limit freq |Grid reconnect threshold frequency-lower limit, bias of nominal frequency| -0.1 (+60Hz) |
@@ Line 81: / Line 85: @@
 ==== Volt-Watt  ====
 ^Parameter on HMI (legacy name before M1330)  ^Meaning   ^HECO requirement  ^CA rule 21 requirement  ^IEEE1547 requirement  ^
-|Setting -> AC -> Page 8 -> Volt/Watt V1	|Volt-Watt V1	|1.06 (*480V)	|
+|Setting -> AC -> Page 8 -> Volt/Watt V1	|Volt-Watt V1	|1.06 (*480V)	|1.06 (*480V)	|1.06 (*480V)	|
 |Setting -> AC -> Page 8 -> Volt/Watt ramp rate	|useless, cancelled in V1440 |0	|
-|Setting -> AC -> Page 8 -> Volt/Watt delay	|Volt/Watt return delay	|60 s	|
+|Setting -> AC -> Page 8 -> Volt/Watt delay	|Volt/Watt return delay	|60 s	|60 s	|60 s	|
-|Setting -> AC -> Page 8 -> Volt/Watt V2	|Volt-Watt V2	|1.1 (*480V)	|
+|Setting -> AC -> Page 8 -> Volt/Watt V2	|Volt-Watt V2	|1.1 (*480V)	|1.1 (*480V)	|1.1 (*480V)	|
-|Setting -> AC -> Page 8 -> Volt/Watt P1	|Volt-Watt P1 	|1 (*power setpoint)	|
+|Setting -> AC -> Page 8 -> Volt/Watt P1	|Volt-Watt P1 	|1 (*power setpoint)	|1 (*power setpoint)	|1 (*power setpoint)	|
-|Setting -> AC -> Page 8 -> Volt/Watt P2	|Volt-Watt P2	|0 (*power setpoint)	|
+|Setting -> AC -> Page 8 -> Volt/Watt P2	|Volt-Watt P2	|0 (*power setpoint)	|0 (*power setpoint)	|0 (*power setpoint)	|
-|Setting -> AC -> Page 8 -> Volt/Watt response time	|Volt-Watt response time|10 s	|
+|Setting -> AC -> Page 8 -> Volt/Watt response time	|Volt-Watt response time|10 s	|10 s	|10 s	|
 ==== Freq-Watt ====