Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
manual:module-based:module-based_models_firmware_updating_instruction [2019/04/17 21:24] admin [Before updating] |
manual:module-based:module-based_models_firmware_updating_instruction [2020/09/16 22:16] (current) |
||
|---|---|---|---|
| Line 27: | Line 27: | ||
| ===== Before updating ===== | ===== Before updating ===== | ||
| + | <WRAP center round important 60%> | ||
| + | Make sure the inverter is **NOT** running. | ||
| + | </ | ||
| + | |||
| <WRAP center round tip 60%> | <WRAP center round tip 60%> | ||
| Updating priority sequence, unless informed by us: | Updating priority sequence, unless informed by us: | ||
| Line 32: | Line 36: | ||
| - AC modules, | - AC modules, | ||
| - U2. | - U2. | ||
| - | </ | ||
| - | |||
| - | <WRAP center round warning 60%> | ||
| - | Make sure the inverter is not running. | ||
| </ | </ | ||
| Line 69: | Line 69: | ||
| <WRAP center round important 60%> | <WRAP center round important 60%> | ||
| - | In HMI version 1330 or earlier, the Updating page is not available in English, you have to log in with a operator password and change the language to Chinese. You can check the following 4 English-Chinese comparing figures to find how to change it back to English again. | + | In HMI version 1330 or earlier, the **Updating** page is not available in English, you have to log in with an operator password and change the language to Chinese. You can check the following 4 English-Chinese comparing figures to find how to change it back to English again. |
| Login and then you can see all the menus. | Login and then you can see all the menus. | ||
| - | In HMI version 1340 or later, the Updating page is English. | + | In HMI version 1340 or later, the **Updating** page is English. |
| </ | </ | ||
| {{: | {{: | ||
| Line 89: | Line 89: | ||
| Open the front door, plug the USB disk to the USB port of the HMI | Open the front door, plug the USB disk to the USB port of the HMI | ||
| - | <WRAP center round warning | + | |
| + | <WRAP center round important | ||
| Make sure that the HMI firmware: monitor.tar.gz, | Make sure that the HMI firmware: monitor.tar.gz, | ||
| </ | </ | ||
| + | |||
| + | |||
| {{: | {{: | ||
| Line 100: | Line 103: | ||
| - | - Enter the Upgrade page in Settings. | + | - Enter the **Upgrade** page in Settings. |
| - Select Type as **DCAC**, and **Module** | - Select Type as **DCAC**, and **Module** | ||
| - Check all the modules that need to be updated | - Check all the modules that need to be updated | ||
| Line 112: | Line 115: | ||
| To UPDATE U2 Firmware, just repeat the procedures above, the differences are: | To UPDATE U2 Firmware, just repeat the procedures above, the differences are: | ||
| - | - Select Type as U2 | + | - Select |
| - Check on #11 | - Check on #11 | ||
| - | - Click Import, Select U2_V[version].hex | + | - Click **Import**, Select U2_V[version].hex |
| + | |||
| + | ===== After Updating ===== | ||
| + | <WRAP center round important 80%> | ||
| + | Before leaving the site, DO remember to set the HMI to **Remote Control mode** if it was not in this mode! | ||
| + | </ | ||